Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m
Self-sealing aluminum pipe insulation tape — 50 mm × 10 m

Self-sealing aluminum pipe insulation tape — 50 mm × 10 m (frost protection)

  • Sales unit – 1 roll of 50 mm × 10 m.
  • Structure – insulating foam with a self-sealing aluminum film (it closes onto itself when overlapped).
  • Use – insulation and frost protection for hot/cold water pipes, heating and HVAC.
  • Quick installation – wrap it around the pipe; no need to dismantle the system.
  • Cuttable – trim to size with ordinary scissors; clean application on a dry, degreased surface.
  • Note – not a heat-shrink sleeve; suitable for moderate operating heat and protection from cold and condensation.
£12.75
Tax included

 

Self-sealing aluminum pipe insulation tape — 50 mm × 10 m

Reduce heat loss, condensation and the risk of frost on your pipes with this 50 mm × 10 m insulation roll. The aluminum foil surface reflects radiant heat and the foam underneath improves the insulation: it is wrapped directly around the pipe and seals onto itself without any additional glue.

What it is for

  • Outdoor frost protection for exposed pipes (water, heating, irrigation).
  • Insulation of indoor and technical sections to reduce heat loss and condensation.
  • HVAC: ducts and refrigerant lines, flow and return sections near boilers and heat pumps.

Why choose it

  • Self-sealing: it closes when overlapped, for quick and clean installation.
  • Reflective aluminum: helps against radiant heat and protects the foam.
  • Flexible & cuttable: adapts to bends and fittings, trimmed with scissors.
  • No dismantling: wrap and secure, the system stays in operation.

How to apply it (4 steps)

  1. Clean the pipe: dry, free of dust and grease.
  2. Measure the section and cut the length you need.
  3. Wrap with a 30–50% overlap, keeping an even tension.
  4. Seal the ends; outdoors, protect exposed joints with a suitable aluminum tape.

Technical specifications

Roll size 50 mm (width) × 10 m (length)
Composition Foam insulating layer + aluminum foil facing
Application Wrapped directly around the pipe (self-sealing)
Environment Indoor/outdoor; avoid standing water on joints
Unit 1 roll

Important notes

  • Not heat-shrinkable and not suitable for direct contact with red-hot parts (exhausts, burners).
  • Check local regulations on insulation and reaction to fire in technical rooms.
  • For maximum effectiveness outdoors, protect the joints and reduce thermal bridges around the supports.

Contents

1 × roll of pipe insulation tape 50 mm × 10 m.

FAQ

Is adhesive needed? No: the strip is self-sealing and closes onto itself. Outdoors you can reinforce the ends with aluminum tape.

Is it suitable for heating systems? Yes, it is designed for hot and cold water pipes and HVAC as a wrap-around insulation strip.

How much overlap? 30–50%, depending on exposure and the desired thickness.

901905

16 other products in the same category: